| H00G-00 | 0.7 | 0.9 |  |  |  | High stiffness grade for containers such as auto under-hood reservoirs |
| R01A-00 | 1.8 | 0.8 | | | | Balance of stiffness, impact, contact clarity; suitable for hot fill |
| R01C-00 | 2.1 | 9.8 | | | | Clarified grade with balance of stiffness, impact; suitable for hot fill |
| R01C-01 | 2.1 | 8 - 10 | | | | Clarified, low plate-out grade with balance of stiffness, impact; hot fill |
| R05C-00 | 5 | 0.8 | | | | Clarified grade used as gloss layer; also suitable for injection blow molding |
| R12C-00 | 12 | 1.9 | | | | Clarified grade for injection blow and injection stretch blow molding apps |
| R12C-01 | 12 | 1.9 | | | | Low antistat, clarified grade for injection stretch blow molding |
| | | | | | | |
| H00G-00 | 0.7 | 0.9 | | | | General purpose homopolymer sheet grade |
| H01F-00 | 0.7 | 0.7 | | | | Low flow rate, barefoot homopolymer powder grade |
| H01G-00 | 1.2 | < 1 | | | | General purpose homopolymer grade for thermoforming applications |
| H01H-00 | 1.6 | 1.8 | | | | Long-term heat aging homopolymer grade for thermoformed sheet |
| H02C-00 | 2.2 | 0.6 | | | | Clarified homopolymer grade for thermoformed packaging |
| H02C-01 | 2.2 | < 1 | | | | Low plate-out, clarified homopolymer grade for thermoforming |
| H02G-00 | 2.8 | < 1 | | | | General purpose homopolymer OPP film grade |
| H02G-02 | 2.0 | | | | | General purpose homopolymer for BOPP, tape, twine, woven bag and thermoformed sheet |
| H02S-00 | 2.8 | < 1 | | | | Homopolymer OPP grade with slip agent |
| H03BLME | 3.5 | <1 | | |  | General purpose extrusion grade |
| H03G-00 | 3.2 | < 1 | | | | General purpose homopolymer extrusion grade |
| H03G-01 | 3.4 | 0.4 | | | | General purpose homopolymer extrusion grade |
| H03G-02 | 3.5 | < 1 | | | | General purpose homopolymer fiber grade |
| H03G-04 | 3.5 | < 1 | | | | General purpose homopolymer OPP film grade |
| H03SLME | 3.5 | <1 | | | | General purpose extrusion grade |
| H03W-00 | 3.5 | < 1 | | | | General purpose low water carry-over homopolymer grade |
| H03W-01 | 4.0 | < 1 | | | | Low water carry-over homopolymer for cordage, carpet backing, industrial fabrics, and geotextiles |
| H03W-03 | 4.0 | < 1 | | | | Low water carry-over homopolymer with good thermal stability for cordage, carpet backing, industrial fabrics, and geotextiles |
| H03YLME | 3.5 | <1 | | | | General purpose extrusion grade |
| H04F-00 | 4.0 | 0.5 | | | | Medium-low flow rate, barefoot homopolymer powder for compounding |
| H07B-00 | 7.3 | < 1 | | | | Homopolymer with anti-block for cast film |
| H07B-01 | 7.3 | < 1 | | | | Nucleated homopolymer with anti-block for cast film |
| H07D-00 | 7.3 | < 1 | | | | Homopolymer with slip agent and anti-block for cast film |
| H07F-00 | 7.5 | 0.4 | | | | Medium flow rate, barefoot homopolymer powder for compounding |
| H08U-00 | 9.0 | < 1 | | | | UV stabilized homopolymer for fiber spinning |
| H11G-00 | 11.0 | < 1 | | | | Barefoot homopolymer for staple and oriented yarn |
| H12F-00 | 12.0 | 0.4 | | | | High melt flow, barefoot homopolymer powder for compounding |
| H19G-00 | 19.4 | 0.5 | | | | General purpose fiber grade homopolymer |
| H20A-00 | 20 | 0.4 | | | | Injection molding grade with moderate levels of antistat |
| H36G-00 | 36 | 0.4 | | | | Homopolymer designed for textiles, filtration media, disposable fabrics and cloth |
| H36G-01 | 36 | < 1 | | | | Homopolymer for spunbonded nonwovens and partially oriented yarn (POY) |
| H38G-02 | 38 | < 1 | | | | Homopolymer for spunbonded nonwovens and partially oriented yarn (POY) |
| N00M-00 | 0.5 | NB | | | | Impact copolymer with good stiffness/impact balance for high impact thermoformed packaging |
| N01N-00 | 1.9 | NB | | | | Impact copolymer with good stiffness/impact balance for freezer-to-microwave thermoformed packaging |
| N02G-00 | 2.5 | NB | | | | Impact copolymer with good stiffness/impact balance for high impact thermoformed packaging |
| N02J-00 | 1.9 | NB | | | | Impact copolymer with good stiffness/impact balance for freezer-to-microwave thermoformed packaging |
| N05U-00 | 5.0 | NB | | | | UV stabilized grade for materials handling |
| R01A-00 | 1.8 | 0.8 | | | | Extrusion blow molding random copolymer suitable for hot-fill applications |
| R01C-00 | 2.0 | 9.8 | | | | Clarified, antistated random copolymer for blow molding and thermoforming |
| R01C-01 | 2.0 | 8-10 | | | | Low plateout version of R01C-00 |
| T00G-00 | 0.6 | NB | | | | Special fractional melt flow rate impact copolymer designed for highly flexible, high impact, soft touch and certain FDA applications |
| H05A-00 | 4.7 | 0.5 | | | | Antistated, general purpose homopolymer for closures and tubing |
| H05H-00 | 5.0 | 0.6 | | | | High crystallinity, long-term heat aging homopolymer for appliances |
| H05H-01 | 5.7 | 0.5 | | | | Long-term heat aging homopolymer for appliances and automotive |
| H05M-00 | 5.2 | 0.5 | | | | Medium-term heat aging homopolymer for appliances & compounding |
| H12BLME | 12.0 | <1 | | | | General purpose injection molding grade |
| H12E-00 | 12.0 | 0.5 | | | | Homopolymer grade with high antistat level for closure applications |
| H12G-00 | 12.0 | 0.5 | | | | General purpose homopolymer for consumer and closure applications |
| H12SLME | 12.0 | <1 | | | | General purpose injection molding grade |
| H12YLME | 12.0 | <1 | | | | General purpose injection molding grade |
| H12Z-00 | 12.0 | 0.5 | | | | Antistated, nucleated homopolymer for consumer & closure applications |
| H12Z-02 | 12.0 | 0.5 | | | | Antistated, nucleated homopolymer for closure applications |
| H13M-00 | 13.5 | 0.5 | | | | Medium-term heat aging homopolymer for packaging, closures & consumer products |
| H14A-00 | 14.5 | 0.4 | | | | Antistated homopolymer for packaging, closures & consumer products |
| H18A-00 | 18.0 | 0.4 | | | | Antistated homopolymer for packaging, closures & consumer products |
| H20A-00 | 20 | 0.4 | | | | Injection molding grade with moderate levels of antistat |
| H20BLME | 20 | <1 | | | | General purpose injection molding grade |
| H20E-00 | 20 | 0.4 | | | | Injection molding grades with high level of antistat |
| H20G-00 | 20 | < 1 | | | | General purpose homopolymer for consumer, housewares, and rigid packaging |
| H20H-00 | 20 | 0.5 | | | | Long-term heat aging homopolymer for appliances, consumer, housewares, and rigid packaging |
| H20SLME | 20 | <1 | | | | General purpose injection molding grade |
| H20YLME | 20 | <1 | | | | General purpose injection molding grade |
| H20Z-00 | 20 | 0.4 | | | | Antistated, nucleated homopolymer for consumer and rigid packaging |
| H20Z-03 | 20 | 0.3 | | | | Antistated, nucleated homopolymer for consumer and rigid packaging |
| H28E-00 | 30 | 0.3 | | | | Homopolymer with high antistat levels for consumer, rigid packaging and closures applications |
| H30Z-00 | 30 | 0.4 | | | | Antistated, nucleated homopolymer for consumer and closures applications |
| H35A-00 | 35 | < 1 | | | | Antistated homopolymer for rigid packaging and housewares applications |
| H35G-00 | 35 | < 1 | | | | General purpose, high flow homopolymer for rigid packaging and housewares |
| H35G-GP | 35 | <1 | | | | High melt flow homopolymer for injection molding applications |
| H35G-01 | 35 | 0.7 | | | | General purpose, high flow homopolymer for rigid packaging and housewares |
| H35Z-00 | 35 | 0.4 | | | | Antistated, nucleated, high flow homopolymer for rigid packaging and housewares |
| H35Z-GP | 35 | 0.4 | | | | Antistated high flow homopolymer for injection molding applications |
| H35Z-02 | 35 | 0.4 | | | | High crystallinity, antistat and nucleated homopolymer for molding and compounding |
| H53N-00 | 53 | 0.4 | | | | High flow, nucleated homopolymer for thin wall injection molding and media packaging |
| 3560 | 20 | NB | | | | Impact copolymer with good stiffness/impact/flow balance for non-FDA materials handling applications |
| 3950 | 35 | 2.5 | | | | High flow impact copolymer for automotive interiors |
| L06Z-00 | 6.0 | 3.0 | | | | Antistated, nucleated impact copolymer for injection and compression molded caps |
| L12N-00 | 12.0 | 2.2 | | | | High gloss, nucleated impact copolymer for automotive, consumer and housewares applications |
| L12Z-00 | 12.0 | 2.5 | | | | Antistatted and nucleated impact copolymer for housewares, consumer products and toys |
| L12Z-01 | 12.0 | 3.5 | | | | High gloss, nucleated and antistatted impact copolymer for automotive, toys, consumer and housewares applications |
| L24G-00 | 24 | 3.0 | | | | Antistated impact copolymer suitable for housewares and consumer products |
| L34N-00 | 35 | 2.5 | | | | Nucleated, low gloss impact copolymer for housewares and consumer products |
| N05G-00 | 5.0 | NB | | | | Impact copolymer with good stiffness/impact balance for materials handling |
| N07N-00 | 7.2 | NB | | | | Nucleated impact copolymer with good stiffness/impact balance for materials handling and consumer products |
| N20G-00 | 20 | NB | | | | Impact copolymer with good stiffness/impact balance for toys and consumer products |
| N20L-00 | 20 | NB | | | | Impact copolymer with good stiffness/impact balance for consumer products and material handling applications |
| N20N-00 | 20 | NB | | | | Nucleated and antistatted impact copolymer with good stiffness/impact balance for materials handling, toys and consumer products |
| R08S-00 | 8.0 | < 1 | | | | Random copolymer with slip agent |
| R10G-00 | 10.0 | 0.8 | | | | General purpose random copolymer for consumer products and housewares |
| R12C-00 | 12.0 | 1.9 | | | | Low antistat clarified random copolymer for consumer products |
| R12C-01 | 12.0 | 1.9 | | | | Higher antistat version of R12C-00 |
| R35C-00 | 35 | 0.9 | | | | Clarified random copolymer for thin wall, housewares and rigid packaging applications |
| R35C-01 | 35 | 0.9 | | | | Antistated version of R35C-00 |
| T20N-00 | 20 | NB | | | | Special high melt flow, nucleated and high impact copolymer for consumer applications. |
